How To Repair Outdoor Wicker Furniture

Introduction

If you accept to repair wicker furniture where the wicker reed is missing or damaged and yous are looking for someone to do it for you lot, your probably in for a rude enkindling. Finding someone that is knowledgeable and willing to help y'all will be difficult to discover to say the to the lowest degree and the price will most probable be prohibitive if yous have significant impairment.In some cases, you may notice that the repair may cost more the value of the piece of furniture. In which case yous need to think about repairing it your self. If the article of furniture piece is from a matching gear up or just one you really like, you will most likely want to pursue fixing it rather than replacing it. A reasonable solution in such a case is to do it your self and save your damaged piece from the scrap pile. It'due south a bit tedious simply worth while and definitely doable.

The accompanying images of this article show repairs of a wicker love seat that was damaged past a canis familiaris that chewed the reed. The color and size of reed match was not possible. And then, we used the closest matching reed nosotros could observe. The client was very satisfied because we were able to save her furniture which was function of a matching gear up that was no longer bachelor.

Broken Wicker Reed of Dear Seat Arm

Broken Reed on Love Seat Arm

Cleaved Wicker Reed

Tools You Might Demand

Conventional Pliers
Needle Olfactory organ Pliers
Wire Cutters
Wire the consistency of a Newspaper Clip

Replacing Missing or Damaged Wicker Article of furniture Reed

Repairing wicker furniture sounds hard and in some cases information technology can exist. Yet, this lesson concentrates on replacing missing or damaged reed that is woven in 1 management and not intended for highly complicated woven sections. Minor repairs are very easy and doing it yourself can exist a very rewarding experience. Once you get the feel for information technology, it'southward not bad at all and information technology does all the same, have a piffling patience.

Repaired Wicker Reed

Wicker Reed Repair

reed

10-Steps to Replace Missing or Damaged Reed

1. Identify Damaged Reed

The start thing you demand to do is assess the damage you lot want to repair and make up one's mind if but re-weaving will practise a satisfactory chore. If the damaged wicker reed is piece of cake to view, determine how extensive the damaged or missing reed is. You want to take a good handle on what repairs you demand to brand.

2. Place Reed Material: Shape, Size & Color (Resin or Natural Reed)

To fix for replacement you need to identify what type of material you need along with the diameter and color of the reed. Wicker tin can be manufactured using natural or synthetic resin materials. Whether y'all utilise natural or resin reed, the style and size of the reed can vary and then can the colors.

3. Have a Sample of Reed if Possible

In order to acquire the right replacement reed, y'all might need to take a sample from the damaged reed or from a piece of reed that has excess sticking out from a curtained place nether the furniture. If y'all can acquire a sample yous can show the vendor, you have a meliorate take chances of getting the correct replacement or one close plenty you can live with from them.

4. Determine Quantity of Reed Needed

You will accept to estimate the amount (length) of each slice of reed you will need to practise the repairs. Make sure y'all estimate and then add a little more than. When y'all place your order remember, having left over is a good thing. When yous society, consider having some spare reed on hand for the future. It'southward a inexpensive insurance policy if you accept to make repairs again.

5. Contact Wicker Dealer and Acquire New Reed

The offset identify to go to get replacement reed is from the place you purchased the piece of furniture in an attempts to learn the same reed. If that does not piece of work, you volition need to talk to a wicker dealer that can obtain repair supplies. Natural wicker reed is rather easy to acquire whereas resin reed is more hard because there are so many different vendors with many different types, sizes and colors. Not all reed will be able to be replaced with an verbal match and yous might have to settle with an off colour or off size. Our feel is that the war wounds add a little graphic symbol to your furniture.

six. Notice and Take Note of the Weave Pattern

Before you lot begin, yous volition demand to study the weave design. One time yous remove the damaged reed, y'all may non recognize the pattern that y'all need to re-create when you lot wave the new reed back in. And then wait at information technology closely and understand how you lot must weave the new reed back in. Information technology'south helpful to wait on the reverse side of the furniture (Case: Left arm v.s. correct arm.) and run across what it looks like in an area that is non damaged or missing reed. Taking a articulate picture might help also.

seven. Remove Damaged Reed

Cut and remove the damaged reed with a pair of wire cutters or similar tool. Back out the end of the remaining reed so that the finish is aiming down away from the surface.Leave at least i-2 inches of the original reed tucked downward under the surface. To keep a piece of reed in identify properly, the more y'all weave information technology in the better information technology holds. So, if you can, endeavour to remove enough original reed and so that you can weave dorsum in a pice over and under the cantankerous members at to the lowest degree four to seven times, more than if yous like. In small areas you may have no other choice but to employ a short weave over and under 2-iii cross members. In those cases, yous might accept to alive with it existence a picayune loose when you weave the new piece in. Simply its perfectly adequate every bit long as the woven piece does not fall out.

8. Make a Wire Tool to Assist in Pulling the Reed Support

When you lot set to weave the new reed in place, you volition need a tool to help yous in performing the weave. The reed volition exist woven over and nether the cross member. Yous will non exist able to pull the reed back up to the surface without a wire tool to hook and pull upward the reed. Form a wire tool from a paperclip or like sized wire and so that when y'all feed the stop of the pikestaff down over a cross fellow member, you can take hold of it with the wire and pull up up again from under the next cross fellow member.You demand to bend ane end of the wire to course a hook sufficient to grab the reed and pull it support to the surface. You lot might have to experiment a bit to become information technology to work the way you want it to. Keep the claw slender because it needs to pull the pikestaff upwards and between the laterals. Bend the opposite end so that your information technology gives your finger something to pull up on the tool when your pulling the reed up.

9. Cut and Weave New Reed Into Place (Constrict In Ends Where Necessary)

New reed is unremarkably available in lengths of more than 36 inches. This will commonly exist longer than what you need to repair whatsoever one reed slice. If you tin, employ the whole length when weaving so cut the excess off when your almost done and so as not to waste what y'all purchased. If waste is non an issue or the length is too bothersome, it might exist easier to cut lengths that are easier to piece of work Just don't cutting them short or you will be wasting reed.Use the wire tool y'all made to assist y'all weave the reed in place. The tool has a hook on the end that help you grab the stop of the reed that is downward beneath the surface so that you tin can pull it dorsum up in a higher place the surface to complete the pattern.

Note: Natural wicker reed will need to be soaked in h2o for at least fifteen minutes to get in flexible enough to curve prior to weaving.

10. Stain and Seal Natural Wicker

If you are repairing a natural wicker product, you will need to stain or paint it to friction match your finish. If you are staining and non painting, you lot should seal the stained reed with a articulate acrylic paint after its stained and dry. You lot won't need to paint or seal if your wicker is natural and untreated. Go to your hardware store and buy the smallest amount of stain yous can find. Follow the manufacturers instructions for staining. Purchase a tin can of acrylic spray articulate coat and paint the affected area to seal it. You lot can use the tin can to reseal the entire piece if you like.

If you lot demand to paint the repair, y'all can do merely the area that has been repaired or do the whole thing to make the finish even. Y'all can refer to ourPainting Wicker Furniture or Tips for Painting Wicker Furniture articles for guidance.

Its important to remember 2 things:

Y'all will need more length than the linear distance betwixt start and cease of your weave because the weaving action takes upwardly more than reed than you might otherwise await.
Leave at least an boosted ii inches excess at the cease of each side of the new reed and so that information technology can't pull out the you put the finished ends tucked under the surface where they can't be seen.

Summary

After you accept replaced each piece of damaged or missing reed, the weave should be tight, not too loose. Sometimes its indvitable to have a loose weave in a repair, but information technology much better to exist loose than cleaved or missing. In most cases yous will have repaired your wicker furniture with smashing successand you volition feel pretty good that you learned how to repair information technology yourself and be surprised how adept it looks. Recognize that the new piece of reed will generally withstand the aforementioned clothing that the original did.

Don't forget to Like Us on Facebook and Follow united states on Twitter to receive more weblog updates.

Source: https://www.wickerliving.com/blog/10-steps-to-repair-missing-or-damaged-wicker-furniture-reed/